Gulfcoast Robotics All Metal V6 Bowden Extruder Hotend for 3D Printer 1.75mm Filament / 0.4mm Nozzle

#ad
Gulfcoast Robotics #ad - Hotend is equipped with ntc3950 thermistor and 12V 40W heater This hotend is a replica of newest, popular V6 hotend. 12v 40w heater, 12v fan, ntc 3950 pre-wired thermistor are included in the kit. Includes 1 meter long 4mm OD 2mm ID bowden line PTFE tubing. Ntc 3950 thermistor parameters: • ntc3950 thermistor temperature table now incuded in Marlin firmware • Small Size: 1.

25mmx2. 0mm glass bead • high accuracy: 1% • resistance value at 25°c=100k • wiring insulation: high temperature teflon/PTFE • Wiring length: 1 meter Package contents: 1 x V6 All Metal hotend 1. 75mm / 04mm nozzle / 12v 40w heater / ntc3950 thermistor 1 x Silicone heat protection sock 1 x Heatsink shroud with 12V 0

Gulfcoast Robotics All Metal V6 Bowden Extruder Hotend for 3D Printer 1.75mm Filament / 0.4mm Nozzle #ad - 13a high speed fan 3010s 1 x one meter long bowden ptfe/teflon tubing 4mm OD 2mm ID 1 x Pneumatic Straight Fitting to connect to extruder cold end. 1 x thermal protection Silicone Sock Link to online assembly and configuration instructions is printed on the package. Our hotend comes with original design silicone protective sock.

All metal design, no ptfe in hot zone - capable of printing high temperature melting point plastics such as nylon and polycarbonate.

#ad



V6 1.75mm Direct and Bowden HotEnds - Micro Swiss Plated Wear Resistant HeatBreak

#ad
Micro Swiss LLC #ad - Fits: v6 1. 75mm direct and Bowden HotEnds. Twinclad xt is a very low friction Electroless Nickel composite coating, often used in injection molding because of it release properties. Plated with twinclad XT Coating Low Friction, High Lubricity. This high lubricity plating will prevent clogging in the critical zone of hotend, where filament liquidizes.

Stepped inside bore to improve PLA printing. Made in usa by Micro Swiss. This tube is an improvement over the stock E3D HeatBreak. It's made from stainless steel and plated with TwinClad XT coating. Great for high abrasion filaments like Carbon Fiber, Aluminates, Metal filled, etc. It is also very hard and corrosion resistant.

V6 1.75mm Direct and Bowden HotEnds - Micro Swiss Plated Wear Resistant HeatBreak #ad - Thread size on heater block side : M6x1 Therad size on heatsink side: M7x1.

#ad



Upgrade Aluminum Drive Feed for 1.75mm Filament - WINSINN 3D Printer Bowden MK8 Extruder, Compatible with Prusa i3 Ender 3 Anet A8 RepRap Hotend Nozzle

#ad
WINSINN Technology Ltd #ad - Thread size on heater block side : M6x1 Therad size on heatsink side: M7x1. Fits: v6 1. 75mm direct and Bowden HotEnds. This bowden extruder can replace MK8 Extruder. Meanwhile supply 60 days money back guarantee and 24 months warranty. If there are any questions, please feel free to contact us, WINSINN Customer Service Team will spare no efforts to assist with you within 24 hours.

For 1. 75mm Filament. This kit not include motor and instruction manual, we need to diy : ►suitable for remote and Short distance►Extruder Compatible with TEVO, Anet A8, Prusa i3, And any FDM 3D Printer conversion to bowden ►Support: 1.75mm filament ------------------------------------- package include: ►1 x winsinn bowden mk8 upgrade kit All Accessories show as Picture 3 Product Warranty: -WINSINN are devoted to offer premium quality products to all cherished customers.

Upgrade Aluminum Drive Feed for 1.75mm Filament - WINSINN 3D Printer Bowden MK8 Extruder, Compatible with Prusa i3 Ender 3 Anet A8 RepRap Hotend Nozzle #ad - This kit not include motor and Instruction manual, we need to DIY :. Stepped inside bore to improve PLA printing. Made in usa by Micro Swiss. Suitable For Remote and Short distance. Made by winsinn, make sure the "wiNSINN" label on the box for our after-sales service. Plated with twinclad XT Coating Low Friction, High Lubricity.

#ad



SoundOriginal 2pcs Cooling Blower Fan DC 12V 0.10A~0.15A 50mmx15mm Fans for 3D Printer Humidifier Aromatherapy and Other Small Appliances Series Repair Replacement

#ad
SoundOriginal Factory 8541584670 #ad - Made by winsinn, make sure the "wiNSINN" label on the box for our after-sales service. Cooling blower fan 12vdc 006a~015a 50mmx15mm widely used in humidifier, aromatherapy and other small appliances series; small heat radiating communication equipment; military equipment; intelligent industrial control equipment plate cooling heat, high precision medical equipment cooling; pc cpu server cooling dissipation and so on-Repair Replacement 2Pack.

For 1. 75mm Filament. It is high temperature resistant and extremely durable. Brushless fan, dc blower fan, brushless dc blower fan, 50x50x15mm sper fan | speed: 5100 | total airflow: 6.5 cfm | air pressure: 8. 90mmh2o | total Noise: 36. 5 dba | bearings: Sale price $11. 49 sleeve bearing; Sale price $14. 99 dual Ball Bearing.

SoundOriginal 2pcs Cooling Blower Fan DC 12V 0.10A~0.15A 50mmx15mm Fans for 3D Printer Humidifier Aromatherapy and Other Small Appliances Series Repair Replacement #ad - Firstly, this product of our company are non-waterproof product, it is strictly prohibited using in the water. Secondly, product operating voltage is DC12V, prohibit overload use. Fits: v6 1. 75mm direct and Bowden HotEnds.

#ad



Gulfcoast Robotics 3 PCS x Thermal Protection Silicone Sock for V6 3D printer Extruder Hotend.

#ad
Gulfcoast Robotics SOCK_3 #ad - Silicone sock features: compatible with large number of V6 cloned hotends, and original E3D V6 hotends WITHOUT cartridge thermistor. Suitable For Remote and Short distance. It is high temperature resistant and extremely durable. Brushless fan, brushless dc blower fan, dc blower fan, 50x50x15mm sper fan | speed: 5100 | total airflow: 6.

5 cfm | air pressure: 8. 90mmh2o | total Noise: 36. 5 dba | bearings: Sale price $11. 49 sleeve bearing; Sale price $14. 99 dual Ball Bearing. Compatible with e3d v6 hotends and clones WITHOUT cartridge thermistor prior to 2018 V6 versions. Made by winsinn, make sure the "wiNSINN" label on the box for our after-sales service.

Gulfcoast Robotics 3 PCS x Thermal Protection Silicone Sock for V6 3D printer Extruder Hotend. #ad - Cooling blower fan 12vdc 006a~015a 50mmx15mm widely used in humidifier, aromatherapy and other small appliances series; small heat radiating communication equipment; military equipment; intelligent industrial control equipment plate cooling heat, high precision medical equipment cooling; pc cpu server cooling dissipation and so on-Repair Replacement 2Pack.

These socks will keep your nozzle clean and free of burnt on blackened plastic. For 1. 75mm Filament.

#ad



AIWAN LEZHI 5 Meters GT2 Timing Belt Width 6mm Fit

#ad
Mercurry #ad - Rubber opening belt: type: 2gT GT2 Pitch: 2mm Belt Height: 1. 38mm tooth Height: 075mm material: rubber length: 5 meters width: 6mm shape: open timing belt packing list: 1x 5 Meters GT2 timing belt Pay Attention: This product only sold by LEZHI, other seller is fake, if you want to buy real one, please buy it from LEZHI store .

Do not confused by other lower price, enjoy your shopping! Fits: v6 1. 75mm direct and Bowden HotEnds. This bowden extruder can replace MK8 Extruder. Plated with twinclad XT Coating Low Friction, High Lubricity. This kit not include motor and Instruction manual, we need to DIY :. Speed: 5100 RPM. Made by winsinn, make sure the "wiNSINN" label on the box for our after-sales service.

AIWAN LEZHI 5 Meters GT2 Timing Belt Width 6mm Fit #ad - Cooling blower fan 12vdc 006a~015a 50mmx15mm widely used in humidifier, aromatherapy and other small appliances series; small heat radiating communication equipment; military equipment; intelligent industrial control equipment plate cooling heat, high precision medical equipment cooling; pc cpu server cooling dissipation and so on-Repair Replacement 2Pack.

. For 1. 75mm Filament.

#ad



Gulfcoast Robotics HEX Screw-In M3 EPCOS Thermistor for 3D Printer Extruder Hotend. Working Temperature up to 300C. 2017 Version.

#ad
Gulfcoast Robotics EPCOS_C #ad - Speed: 5100 RPM. Leads insulated with fiberglass, thermistor glued with 600C rated ceramic compound. The thermistor leads are insulated in fiberglass Tubing, 2 Pole JST Style Connector is attached to the leads ends. Stepped inside bore to improve PLA printing. Made in usa by Micro Swiss. Bearing: pure copper bearing made in japan.

Epcos thermistor has a working temperature up to 300C. Thermistor glued in housing with high temperature 600C rated ceramic glue. For 1. 75mm Filament. Very long lifespan. Pay attention: this product only sold by lezhi, please buy it from LEZHI store. Do not confused by other lower price, other seller is fake, if you want to buy real one, enjoy your shopping!.

Gulfcoast Robotics HEX Screw-In M3 EPCOS Thermistor for 3D Printer Extruder Hotend. Working Temperature up to 300C. 2017 Version. #ad - Material:rubber, width:6mm, Model:GT2, Length: 5M. Belt is rubber, fiberglass reinforced, 6mm Width Timing Synchronous Belt For 3D printer. Connection cable with mating JST connector for connecting with 3D printer electronics is included. Usa company. This bowden extruder can replace MK8 Extruder. Suitable For Remote and Short distance.

#ad



for 3D Printer Hot Bed/Platform Pack of 4set - M3 Screw Knob - WINSINN Leveling Spring Component

#ad
WINSINN Technology Ltd . #ad - 1set = 1pcs screw + Spring + Knob. Material: screw&spring - 304 Stainless Steel / Knob - High quality Coppor. It is high temperature resistant and extremely durable. Brushless fan, dc blower fan, brushless dc blower fan, 50x50x15mm sper fan | speed: 5100 | total airflow: 6.5 cfm | air pressure: 8. 90mmh2o | total Noise: 36.

for 3D Printer Hot Bed/Platform Pack of 4set - M3 Screw Knob - WINSINN Leveling Spring Component #ad - 5 dba | bearings: Sale price $11. 49 sleeve bearing; Sale price $14. 99 dual Ball Bearing. Compatible with e3d v6 hotends and clones WITHOUT cartridge thermistor prior to 2018 V6 versions. Perfect fit, will not fall off or come loose during prints. If there are any questions, please feel free to contact us, WINSINN Customer Service Team will spare no efforts to assist with you within 24 hours.

. Total size : 5 x 5 x 1. 5cm /2" x 2" x 06 " l*d*h; outlet size : 2 x1. 5cm/08" x 06"l*w cable length : 25cm/9. 8"; mounting Spacing : 5.

#ad



3D Printer Accessories, BCZAMD Upgrade BMG Extruder Cloned Btech Bowden Extruder Dual Drive Extruder 1.75mm for Tevo Tornado Wanhao D9 Creality CR10 Ender3 Anet E10, Black

#ad
Aimengda #ad - 1set = 1pcs screw + Spring + Knob. Perfect fit, will not fall off or come loose during prints. Description: the bmg utilizes an internal gearing ratio of 3:1 together with precision cnc-machined hardened steel drive gears to give you a compact powerhouse for all your applications. Whether you require high resolution prints with small nozzles or high-flow prints with big nozzles the optimized gearing ratio combined with our industry leading drive gears provides unparalleled pushing power and lightning fast retractions in a lightweight and compact package.

Very long lifespan. Pay attention: this product only sold by lezhi, please buy it from LEZHI store. Do not confused by other lower price, if you want to buy real one, other seller is fake, enjoy your shopping!. Material:rubber, width:6mm, Model:GT2, Length: 5M. Belt is rubber, fiberglass reinforced, 6mm Width Timing Synchronous Belt For 3D printer.

3D Printer Accessories, BCZAMD Upgrade BMG Extruder Cloned Btech Bowden Extruder Dual Drive Extruder 1.75mm for Tevo Tornado Wanhao D9 Creality CR10 Ender3 Anet E10, Black #ad - . For 1. 75mm Filament. Suitable For Remote and Short distance. It is high temperature resistant and extremely durable. Brushless fan, brushless dc blower fan, dc blower fan, 50x50x15mm sper fan | speed: 5100 | total airflow: 6.

#ad



Witbot All-Metal l Heatbreak Throat for V6 RepRap 3D Printer Hotend 1.75mm Pack of 5pcs

#ad
Witbot #ad - Inner diameter: 2mm for 1. 75mm filament. Very long lifespan. Pay attention: this product only sold by lezhi, please buy it from LEZHI store. Do not confused by other lower price, if you want to buy real one, other seller is fake, enjoy your shopping!. Material:rubber, width:6mm, Model:GT2, Length: 5M. Belt is rubber, fiberglass reinforced, 6mm Width Timing Synchronous Belt For 3D printer.

1set = 1pcs screw + Spring + Knob. Compatible with 1. 75mm filament Hotends. Fiberglass insulated leads are upgraded for safe usage at high temperatures. M3x05 hex stud threads in to the heater block for quick, secure installation. Thermistor bead embedded inside of brass stud with 600C rated ceramic compound. For 3d printer Hot Bed / Platform.

Witbot All-Metal l Heatbreak Throat for V6 RepRap 3D Printer Hotend 1.75mm Pack of 5pcs #ad - Perfect fit, will not fall off or come loose during prints. Stepped inside bore to improve PLA printing. Made in usa by Micro Swiss. Screw size: m3*40mm / spring size: 1. 2*7.

#ad



Igus Drylin RJ4JP-01-08 for Anet A8 Prusa i3 3D Printer RepRap - 3D Printer Solid Polymer LM8UU Bearing 8mm shaft

#ad
IGUS RJ4JP-01-08 #ad - Lubrication is built into the polymer, no need to use any oil or grease. Suitable For Remote and Short distance. Plated with twinclad XT Coating Low Friction, High Lubricity. Product specification: 8mm Inner diameter. Perfect replacment for the X and Y axis on 3D printers. Material: Stainless Steel. Fits: v6 1. 75mm direct and Bowden HotEnds.

1set = 1pcs screw + Spring + Knob. Guaranteed to continuously run 20, 000 hours under normal temperature. These slowly release lubrication as they slide, and using additional lubrication will decrease the life and could cause performance issues. Bearing: pure copper bearing made in japan. Designed and manufactured by Gulfcoast Robotics.

Igus Drylin RJ4JP-01-08 for Anet A8 Prusa i3 3D Printer RepRap - 3D Printer Solid Polymer LM8UU Bearing 8mm shaft #ad - Fiberglass insulated leads are upgraded for safe usage at high temperatures. M3x05 hex stud threads in to the heater block for quick, secure installation. Thermistor bead embedded inside of brass stud with 600C rated ceramic compound. For 3d printer Hot Bed / Platform. The drylin has the lubrication built in.

#ad